World Model 3000 Coiler

World Model 3000 Coiler

When it comes to producing a versatility of high-quality coils with operator friendly features, you have a pro on your side. It’s the Platt World Model 3000 Coiler! It features everything you want for now… and need for tomorrow.

The Platt World Model 3000 is the result of our sixty-plus years coiling expertise. With the WM 3000 you will be able to coil the widest range of wire gauges, coil outer diameters and coil types than on any other coiler on the market today. The Platt World Model 3000 has a coiling range from 13 gauge to 30 gauge wire with coil O.D.’s ranging from 0.40″ and up. Coils of 1.00″ O.D. have been coiled!

The Platt WM3000 is designed to produce top-quality single, twin, triple, space wound, and with proper setup, non-helical shaped coils from either pail packs or spools. Coils from ribbon / flatwire can also be produced.

No extra device – no extra cost incurred – to produce tandem (twin) coils. The WM3000 comes complete with a Twin Depailer and a Spool Spindle. Special adapters for spools with I.D.’s above 5/8″ can be supplied. As an accessory, a special Triple Depailer and Solution Wheel can be supplied to create triple wire coils.

Optional Add-Ons

  • Recirculation Solution Pump System
  • Triple Depailer & Triple Solution Wheel
  • 3′ or 6′ Gate Extensions or 12′ Gate
  • Draw Cool-X Solution
  • Extra Spool Spindle
  • Spool Adapter

 

Platt Quality
If it is high quality, perfect heat pattern and superb ohmage-controlled coils with near 100% clean cuts that you need, then the Platt Coiler is the answer for you. This unsurpassed accuracy is achieved only on a Platt coiler!

We begin with our patented no-slip Isolator Metering Wheel and 400 Pulse Encoder coupled to our PLC Touch Screen System to electronically measure the traveling wire in increments of as little as 1/16″ (1.55 mm) of straight wire. The ohmage you set is the ohmage you get – period. The PLC Touch Screen System features Jog-Run Mode to start a coil with ease and an automatic shut off Batch Counter. Coil length can be changed without stopping the Coiler. This accuracy is further enhanced with the adjustable Roll Bodies to match the helix of any coil, and our patented adjustable air-indexing, fast acting Air Cutter.

The Coiling Head features our Single-end Spindle designed for interchangeable 200 Series Collets that range from 3/64″ to 1/8″. The Collets can provide for our centerless ground Tungsten Carbide Arbor as small as 0.25″ (.65 mm) and up. With its five-step pulley, the Spindle provides speeds of 1200, 1600, 2600, 3600 and 4600 r.p.m.’s.

The Head features built-in synchronization between the Arbor and Work Rings. The motor drives the Spindle; whereas the Coil Roll Bodies are powered by 6″ Rubber Friction Drive Rolls coming in contact with the proper Drive Sleeve in the rear. The proper selection of Drive Sleeves on the rear of the Spindle synchronizes the speed between the Coiling Rolls and Arbor to reduce the work on the wire being coiled; therefore producing high-quality coils. Flexible Drive Cables attached to the Friction Drive Rolls and the Pinion Gear System allows the adjustable Roll Bodies to match the helix of any coil. The WM 3000 goes one step further – the Coiling Rolls can be adjusted independently in a horizontal plane. This feature is important in coiling certain wire and with some methods of coiling.

Platt World Model 3000 Specifications
The WM 3000 is designed to meet your precision coiling requirements, and comes complete with the following features:

  • Motor
    120 or 240 volts, 1 horsepower
  • Programmable Logistics Controller (PLC) Touch Screen System
  • Digital Coil Length Control
  • Batch Counter – Four Digit
  • Isolator Unit (Metering Wheel)
  • 400 Pulse Encoder
  • One Spool Spindle
  • Twin Depailer Unit
  • Solution Tray
  • 200 Series Collet Spindle
    Collet range of 3/64″ to 3/8″
  • Five-Step Spindle Pulley
    1200, 1600, 2600, 3600, 4600 r.p.m.
  • Hardened & Ground Angling Roll Body Units
  • 14,22,54 Tooth Set Pinion Gears
  • Full Set Drive Sleeves and Filler Rings
  • Safety Switches
  • Safety Guards
  • Indexing Air Cutter – 2 1/2″ Cylinder
    3 1/4″ or larger Cylinder Air Cutters available; added cost
  • 6 foot hinged, air-operated Coil Collector Tray
  • Base Cabinet
  • Light and Magnifying Lens
  • Machine Tools
  • Instruction Manual and Parts Catalog
  • Platt Premium Service & Support
  • Tooling and Crating are extra

It is the versatility of the World Model 3000 Coiler that will give you everything for today’s and tomorrow’s challenges. Our engineers go out of their way to keep the Platt Coilers on the cutting edge of technology. You can bet if there is a more efficient way of coiling or a new method of coiling, S. A. Platt, Inc. will deliver it.

Now is the time to join the pros with the finest coiling machine and comprehensive knowledge available! Contact us for more information or to receive a quote for your coiling needs.